Home > Sundance Spa > Sundance Spa Error Code Flo2

Sundance Spa Error Code Flo2

Contents

ICE Freeze condition. 55ºF detected. Contact your Sundance Spas dealer or qualified service technician. *Note: This message can also appear if the pump has not regained prime after the hot tub has been drain and refilled. Spacare.com 888-772-9887 Technical Assistance 405-622-4950 0 Item(s) | Total: $0 Home Shop SpaCare.com Spa Part Index Circuit Board Repair Spa Covers Spa & Hot Tub Covers Spa Cover Lifts Sn1 Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). have a peek here

Credentials confirmed by a Fortune 500 verification firm. Loading... The black lead to circulating pump comes from TB 402-2--NOT as I stated TB4-10 Earlier today, I pulled the connector for the flow switch and rang it out--infinity. While it was working, I determined that I had 240v feeding the 12v supply but no DC out.

Sundance Flow Switch

Powered by vBulletin™ Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. my computer skills are poor, sorry Expert: TheHotTubGuy replied4 years ago. YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART. I am not sure if the problem is caused by a thermal issue, or the pump is just worn out.

Sign in 8 Loading... There is no additional charges to you. I would like to pursue additional dialog with you if that does not work and I need to try something else.Jerry : Sure, This question remains open, for 30 days, for Sundance Spa Troubleshooting ehowathomechannel 132,193 views 3:08 No Glitch Flow Switch Installation - Duration: 14:19.

The countdown timer for the UB bulb needs to be reset (Section 12.8, page 58). OH Overheating, water over 112° F. Published on Sep 27, 2014~~Direct Amazon Links~~Official Updated Sundance Flow Switchhttp://www.amazon.com/dp/B0031B6Y9G/?...Parts for this Home-Brew Fix:~Qty:1 ~ 3/4" Threaded PVC Tee:http://www.amazon.com/dp/B008I4D6NI/?...~QTY:1 ~3/4" Male to 3/8 Barb Fittings(10 Pack):http://www.amazon.com/dp/B007IBGAUS/?...~QTY:1 ~ 3/4" Insert w/ Proper water flow is inhibited or flow/pressure switch may be obstructed, misaligned, or defective.Troubleshooting Steps:1.

Remove filter and allow air to bleed out of filter. Sundance Hot Tub Manual If continuity is measured, switch is OK. Temperature Incorrect or OHAnother issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into theOHerror code. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Test new features Loading...

Sundance Spa Flo Error

I can hear a gurgling noise in the heater when the circulating pump is running, could this be an indication of poor flow? hot Overheating, water over 112° F. Sundance Flow Switch Heater is deactivated. Sundance Spa Flow Switch Testing DO NOT ENTER THE WATER!

So--possibly bad circulating pump? navigate here Do not worry, there is not voltage in these wires that can harm you.Now turn the power back on and watch the flow switch, do you see water moving?Is the FLO2 ooops. After putting the right hand panel with the radio back together, I found the radio was not working. Jacuzzi Flo2 Error Code

If the power supply is not available through your local Sundance Support Desk contact our order desk for pricing and availability: [email protected] Ask a Question or Comment Cancel reply Message *Name Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. Sign in to make your opinion count. Check This Out I'm still looking into board schematics.

Brett Spa Side Error Codes For more information Regarding Brett Aqualine tech support click here OH Temp exceeds 118 degrees Fr Freeze condition - temp below 40 degrees FL Pressure switch Sundance Spa Troubleshooting Fl1 Any chance this could just be a failed rely not releasing when the flow switch should be open? Loading...

Copyright © 1995-2016 DoItYourself.com Inc.

Difficult Problem, Please Help FLO2 !!!! With the power off the swing arm should be straight down and not contacting the post next to it.Standing by. So I wired in a standard rocker switch into the flow sensor. Sundance Spa Not Heating Measure resistance across switch terminals for continuity.

ehowathomechannel 132,193 views 3:08 Sundance Spas ~Flow Switch Repair w/Cheap Hardware Store Parts ~Altamar 2001 - Duration: 7:49. Loading... On startup I leave it off and then when I get the FLO (not FLO2) error indicating that the flow switch should now register as closed I flip the switch and http://allconverter.net/sundance-spa/sundance-spa-error-flo2.html Low speed pump and heater will activate until spa reaches 65ºF.

This works great and allows for the heater to come on. Sn2 Nonfunctional temperature sensor. I guess I'm going to call a servive guy. Arctic Spas Utah 41,065 views 1:49 What to do if your hot tub stops heating - Duration: 1:13.