Sundance Spa Code Flo
Please try again. Proper water flow is inhibited or flow/pressure switch may be obstructed, misaligned, or defective.Troubleshooting Steps:1. The Circulation Pump may be plugged up with debris or it is defective. Please email us at this link:http://www.spaandpoolsource.com/contact-us.aspxTech Support is here to assist you in identifying and selecting the right part for your year and model of spa. have a peek here
I think at this point since I'm neither handy or lucky, it may be easiest to replace the pump. Smart Farm 524 görüntüleme 1:17 5 Common Hot Tub Issues and Solutions - Süre: 5:41. Sign Up All Content All Content Advanced Search Browse Forums Blogs Calendar Staff Online Users More Activity All Activity Search More More More All Activity Home Sorry, there is a problem If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate
Sundance Spa Error Codes
If you have one available, I will provide further detail. NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets. Helpful Links: GET A TEST KIT Chlorine/CYA Chart How to SLAM About Metals & Stains Reply With Quote 12-26-2012,02:13 PM #7 Rocco View Profile View Forum Posts View Articles Join
Circ pumps run all the time, constantly filtering the water. Yükleniyor... See Temperature Sensor Diagnostic Guide:http://www.spaandpoolsource.com/sundancespastemperaturesensordiagnostic.aspx6. Sundance Spa Flow Switch Testing We removed the filter, reset the power.
Home Help Search Login Register Hot Tub Forum » General » Hot Tub Forum » 'solid' FLO message on Sundance Spa « previous next » Print Pages:  Author Topic: 'solid' Sundance Spa Flow Switch OPEN or SHORTED SENSOR (heater disabled) The main temperature sensor is non-functional. I also believe that my circulation pump is causing these issues. You should be able to see it close and open.
SerjicalStrike Full Member Posts: 676 Reinstate Hank Williams!! Sundance Spa Pressure Switch See "Water is too hot" (page 77). It does not matter if the error message is FLO or FLO2. If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes
Sundance Spa Flow Switch
Again, thanks to those that took the time to read all this and answer my questions. azurepoolsandhottubs 113.127 görüntüleme 1:13 How To Fix the Air Lock on Your Hot Tub Pump | Arctic Spas - Süre: 1:33. Sundance Spa Error Codes It also said 30 psi (2bar). Sundance Spa Flo2 Error Check interlock jumper located on the sensor harness.
Circulation Pump or 5. navigate here Logged clover Full Member Posts: 475 Re: 'solid' FLO message on Sundance Spa « Reply #6 on: February 17, 2012, 11:02:18 AM » Quote from: SerjicalStrike on February 16, 2012, 03:45:05 Sıradaki Sundance Spas ~Flow Switch Repair w/Cheap Hardware Store Parts ~Altamar 2001 - Süre: 7:49. John Powers 10.494 görüntüleme 1:36 What to do if your hot tub stops heating - Süre: 1:13. Sundance Spa Troubleshooting Fl1
Following is a listing of all the possible messages along with their meanings. Sundance Spa Circulation Pump Yükleniyor... Many service related issues cannot be diagnosed without being infield at the spa.
All rights reserved.
Dilinizi seçin. See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. However after several minutes it reappears.2. Sundance Altamar Flow Switch Mr.
I had one of the small cotton intake covers get sucked into pipes before. I've been doing a lot of reading of the causes. William Kasper 27.025 görüntüleme 10:12 How do flow switches work? - Süre: 1:17. http://allconverter.net/sundance-spa/sundance-error-code-blb.html The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.
It 11/30/2016 11/30/2016 JACUSTOMER-27j3luit- I have a three month old 14000 gallon fiberglass pool. HotTubsByArcticSpas 111.866 görüntüleme 1:33 Balboa Legacy Systems Series - Troubleshooting Panel Message OH - Süre: 4:54. Site by Take 42 Gezinmeyi atla TRYükleOturum açAra Yükleniyor... This must be repaired only be a Sundance Spas dealer or qualified service technician.
Most common cause for Watchdog is the Temperature Sensor. softcellelectrical 50.158 görüntüleme 4:15 Gecko S-Class SSPA Heaters How To Diagnose & Repair The Spa Guy - Süre: 9:59. Try to reset power to spa. Yükleniyor...
The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Geri al Kapat Bu video kullanılamıyor. İzleme SırasıSıraİzleme SırasıSıra Tümünü kaldırBağlantıyı kes Bir sonraki video başlamak üzeredurdur Yükleniyor... İzleme Sırası Sıra __count__/__total__ FLO Error Code Scott Felsen Abone olAbone olunduAbonelikten çık Check secondary screen filter (Solo Models only)5. I can opertate it off the panel switch though, and there is flow.
Is there voltage going to pump, Is there adequate Flow coming out of Heater Port in Spa?Testing to see if Circ Pump or Flow Switch. I wish I could tell you what year and model it is, but my best guess is that it is a Capri. Yükleniyor... Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way.
FLO, FL, FLC, FL1, PS, Blinking Lights Pressure Switch or Flow Switch Failure. Your circuit board does not "KNOW" it is open and goes into self defense to protect the spa heater system with a SOLID FLO message. Quick View