Home > Sundance Spa > Sundance Spa Code Fl1

Sundance Spa Code Fl1

Contents

If not, cut the power again and remove the filters. Spaminator provided by [OzzModz] Spaminator - vBulletin Mods & Addons Copyright © 2016 OzzModz Ltd. Check secondary screen filter (Solo Models only)5. So, this is easy to check on your spa. have a peek here

If all else fails contact our Service Support Desk to book a diagnostic of your Sundance Spa. if it is not working, this would be the source of a temp problem as the heater will not come on.Do any of your other functions work? If the hot tub water is more than -7C cooler than the temperature set point, jets pump #1 and heater will automatically activate to provide freeze protection. Model is sm-909-nhw-18.

Sundance Spa Error Codes

Your filters were just clogged restricting flow through them. I've already learned a ton by lurking and reading posts. January 31, 2014 Reply Dan typically when you have an FL1 code it means the spa is not heating and won't heat until the FL1 code is addressed so you want Tested heater, t-stat, set a call & unit responded.

I truly believe it's an airlock but I can't seem to aleviate the issue. Please add an item to your cart to view shipping cost. No current with a heat call and voltage at j9 and j10 would indicate a bad heater. Sundance Spa Circulation Pump Problem If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error - - - -.

Any suggestions would be appreciated. The time now is 09:07 PM. If you have 240vac here attach your current meter to the J9 wire and check for current. I will re-verify the flow switch.

We do not ship or sell outside of the USA! Sundance Spa Flo Error Turn power on you get the software code 365 and then 8888 heater comes on for 3 to 5 sec. Haven't used it too much lately, but when I went to check chemicals recently, noticed that I am getting error code FL1 flashing intermittently with the temperature. RISK OF HYPERTHERMIA (OVER-HEATING) CAUSING SEVERE INJURY, BURNS, OR WELTS.

Jacuzzi Hot Tub Error Code Fl1

You won't have heat as long the FL1 msg is showing. Patty Dechellis April 13, 2014 Reply My hot tub ia now displaying ICE What do i do? Sundance Spa Error Codes Preceding your first filter cycle Pump 2 operates for 5min to purge water in that side of the plumbing. Sundance Spa Flow Switch Testing Visit our online store if you require a replacement circ pump or PWA.

When I flip in the power I immediately get an FL1 (blinking) - nothing comes on including the circulation pump. navigate here If all else fails contact your local Sundance Spas Support Desk to book a diagnostic of your Sundance Spa. If there is any more info that you guys need from me I will be happy to try and provide it. Could be that part of the plumbing is frozen or you have a bad temp sensor and or bad PWA. Sundance Flow Switch

Should the power return to normal, the PF error will reset itself. I've worked at UPS for almost 15 years and trust them, but again, I just don't want to wait 2+ weeks for the pump to arrive. The message will flash between "blb" and the water temperature. Check This Out If you power the spa back on and the problem goes away then you are good to go.

This is a dangerous condition because the heater could over heat due to the lack of water flow though it. Sundance Spa Troubleshooting Forum Whereas yesterday it was just warm, today it was scalding hot. http://www.aqua-tech.ca Click on Parts and Accesories and then click on the big Yellow button Prices and Availability.

The filter/circulation may also be deactivated).

May 16, 2014 Reply Joseph the PWA is your main circuit board inside the Sentry Control Box. I have a new filter on order right now, but I'm afraid I may have to replace the circulation pump also. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional. Sundance Spa Reset If the spa is 4yrs old you should be able to find the model name of the spa and the date built of the spa on the label affixed to the

In addition to the code, noticed that the pool is registering 72 degrees when it is set to 101. At least I'm heading in the right direction.. This must be repaired only be a Sundance Spas dealer or qualified service technician. http://allconverter.net/sundance-spa/sundance-error-code-blb.html Thanks Randy Knight September 20, 2016 Reply Did you every get an answer on the FL1 error on your Chelsea hot tub.

I'm not at home right now to check model… I can later, I think it's a 2005 Bahia November 13, 2014 Reply Dustin, if you have a 2005 Bahia remove the The Circulation Pump may be plugged up with debris or it is defective. My spa cables are colour coded to European regulations where brown is live and blue is neutral. If debris is present, remove debris, install switch and test system.

I can see the flow switch and water appears to be moving fine. About Us Blog Support Resources Contact Us Call Us: (204) 233-8822 Facebook Twitter Instagram Chat with us! I currently have an order pending from a site that I ordered a new filter, some fix-a-leak, and a couple other items. With the circ pump on and the main pump off (Portofino Models with Circulation Pump), test switch operation with an ohmmeter meter in the continuity position, test for continuity across switch