Home > Sundance Spa > Sundance Optima Spa Error Codes

Sundance Optima Spa Error Codes

Contents

You said that the spa circulation pump feels like it’s working, you should be able to feel a small constant stream of water coming out of the heater return fitting. Usually a SN error code is signaling that one of the sensors is failing, but since you said that it was a possible lighting strike then your circuit board could have Sorry I don't have more info to provide, but I think we can figure it out. If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error - - - -. have a peek here

Contact your Sundance Spas dealer or qualified service technician. "WATCHDOG" (hot tub is deactivated). No action is necessary. But before doing that, make sure that both sensors are properly mounted and fully inserted and that connectors are also clean and fully inserted. Is there a reset button on the control box?

Sundance Spa Flo Error

Doing this will give you full access to the forums, where you will be able to receive personalized advice concerning your pool. TO reset your ClearRay timer, please refer to our "616" reset instructions here.   Contact UsName * E-Mail * Subject * Message * Download A Copy Of This  Here

© Copyright Clogged impellers rarely happen, but is a possibility. I also noticed the ozone indicator on the control board would go on and off eratically.

Contiguous US only - Free Shipping is not available to Alaska or Hawaii. Pumps appear to be working normally. Remove hot tub cover to speed cooling. Sundance Spa Heater Not Working Q: My control panel reads the error code "FL2." What do I do?

Spaminator provided by [OzzModz] Spaminator - vBulletin Mods & Addons Copyright © 2016 OzzModz Ltd. But before you do, remove your spa filter and test to see if SN code goes away, and make sure all valves and jets are open, to rule out flow related If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature. You can program by hitting the temp button and then the jets button to scroll through.

OH means Overheating, as sensed by the hi-limit or temp sensor, and is caused by water not flowing fast enough thru the spa heater. Sundance Spa Circulation Pump When it’s at 12.6 it works better (still tripping with 188 code) ... That is a long life for a hot tub heater. Proper water flow is inhibited or flow/pressure switch may be obstructed, misaligned, or defective.Troubleshooting Steps:1.

Sundance Spa Service Manual

If all seems good, you may have an adjustable pressure switch that can be lowered, or it could also be a faulty pressure switch or flow switch. WATCHDOG Error Code: - - - or - - - - The most common cause of theWatchdogerror code are the sensors, specifically the temperature sensor. Sundance Spa Flo Error Logged Award winning Hot Spring dealer for a gazillion years. Sundance Spa Temperature Sensor Have you tried adjusting the pressure switch?

Did your error code go away? navigate here Q: My control panel displays the error code "616" aka "blb". You may want to call service with this type of issue. Heater is deactivated. Sundance Spa Flow Switch

I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. PSoL Error Message My spa pack is throwing a PSoL error. Could it be the sensor giving a false reading and shutting down the spa.? Check This Out The Flo error randomly appeared and won't go away.

Sensor plugged into jack B is not working. Sundance Spa Troubleshooting Forum Jacuzzi J-365 Flatlined ---- We shut off hot tub because water was too low and went to fill it next day and was empty. To keep the water temp below 106 (independent thermometer reading) the control panel has been set at 91.

So it sounds like the panel is working correct.

HLoH Hi Limit Over Heat. Switch closed while pump is deactivated. If it's the flow switch, that may free it up. Sundance Spa Reset Button The circulation pump is usually the ‘heater pump’, and either the heater tried to come on but water was not being pushed through it from the circulation pump and overheated and

Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog". If it's flashing then that means the flow switch is not closing due to reduced or lack of water going to the spa heater. Do you have a circulation pump in addition to the two speed pump? this contact form Spa Natural Chemistry OEM specifications Omron Ortega Pac-Fab PDC Pentair Picker Pinnacle Pool Systems USA Portage Potter Brumfield Premier Pres:Air:Trol Prozone Purex Rainbow Ramco Raypack Regal Beloit EPC, Inc.

OH Overheating, water over 112° F. OH Message I have a 15 year old Marquis spa that is displaying an OH message which I know indicates that the spa has shut down due to an overheat protection It sounds like your spa pump or motor is having an issue. Please login or register.Did you miss your activation email? 1 Hour 1 Day 1 Week 1 Month Forever Login with username, password and session length News: Welcome to our forum.

Sundance Altamar Hot Tub. Logged Brewman tony Ultimate Member Posts: 2331 2002 Optima Re: Sundance FLO error.... « Reply #10 on: November 14, 2007, 06:41:28 PM » Another thing to check....there is a nylon filter Sn1 Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). A: This is usually a flow switch that is reading the switch is stuck closed.

If I recall it might have been caused by air in the lines (not filling tub properly?) or possibly from obstruction. EC is economy mode and you can turn it on or off on the panel by pressing a specific sequence. Please Input Part # Your cart is empty. *With a $4.95 Handling Fee. You can try removing the spa filter and try running it and see if it goes into hh code mode.

Has anyone experienced this problem with their Sundance spa? The dealer is comming out next week so the spa will have some down time.