Home > Sundance Spa > Sundance Error Messages

Sundance Error Messages

Contents

Check for clogged filter. The equipment stays on until the sensors detect that the spa temperature has risen to within 20 degrees of the set temperature. We turned it off finished filling it up and turned it back on. You could also drain the spa, disconnect the unions and stick your finger inside the pump housing to try and turn the impellor. have a peek here

It's annoying to say the least to have to go outside every few minutes to manually turn the jets on in order to bring the water temp up. No 240vac here with a heat call would indicate a bad PWA. Low speed pump and heater will activate until spa reaches 65ºF.OH = High temperature condition, has reached 110ºF. Has anyone experienced this problem with their Sundance spa?  The dealer is comming out next week so the spa will have some down time.

Sundance Spa Error Codes

If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance Spa. Proper water flow is inhibited or flow/pressure switch may be obstructed, misaligned, or defective.Troubleshooting Steps:1. Logged "Growing older but not up..." tony Ultimate Member Posts: 2331 2002 Optima Re: Sundance FLO error.... « Reply #8 on: November 14, 2007, 06:58:27 AM » Did you try the

Start with installing a brand new filter and checking for proper flow from your circulation heating jet. If condition still exist, replace switch.) if switch measures infinite (no continuity) with pump off, switch is OK, Turn on Main pump and measure across switch terminals for continuity. That happened to me one time several years ago- and tapping the switch worked, and it been fine ever since. Sundance Spa Heater Not Working The initial code was an FL1 and we realized it didn't have enough water in it.

If flashing by itself, spa is shut down. Sundance Spa Troubleshooting Fl1 The circulation pump doesn't seem to run ever. We have turned the hot tub off and on numerous times and tried both filters with no luck. If the Flow Switch test OK in all the above instances, check switch wiring harness.

http://www.aqua-tech.ca Click on Parts and Accesories and then click on the big Yellow button Prices and Availability. Sundance Hot Tub Manual Justin L. And kicks out and starts all over again please help. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Sundance Spa Troubleshooting Fl1

I just don't have enough experience ordering spa parts yet and thus don't know the good sites to use. This means I might get my order by 2015. Sundance Spa Error Codes The cheapest replacement I found was about $100, all the way up to $200+. Sundance Flo Error In the manual I don't see "test points 18 &19" on TB1.

Contact qualified service technician. navigate here Click Here Please Technical Support Home | Sitemap | About Us | Contact Us | My Account | Shipping Policy | Return Policy | Privacy Policy | Low-Price Guarantee | Cart It could just be a valve or clogged up with hair. Smith Electrical Products Action Spas Acura Advanced Spa Design Advantage Pools and Ponds Air Pro Air Supply of the Future Alladin Allied Innovations American Products American Whirlpool Ametek Anderson Manufacturing AO Sundance Spa Flow Switch

Also check that there is no blockage in the impellor assy of your stage 1, 2-speed pump. Nigel November 14, 2016 Reply Tonja, check with your multimeter that you have proper voltage at the circ pump setpoints on the PWA with a heat call. Gently tap it a couple times with the handle of a screwdriver or something similar. http://allconverter.net/sundance-spa/sundance-spa-error-flo.html May 05, 2014 Reply Brian what make and model spa do you have and what is the date built of the spa?

Control head always displays current temp + error code if set. Sundance Spa Flo2 Error When the spa goes into the Watchdog the spa will not operate.This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on January 31, 2014 Reply Dan typically when you have an FL1 code it means the spa is not heating and won't heat until the FL1 code is addressed so you want

Power on the spa must be cycled before the heater will function again.

YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART. The heater must have come on at some point because the water has warmed up to 70 degrees from around 50 when I filled it. If you DIY, you're going to need to google the make and model to get the repair manual. Sundance Spa Reset Button Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

If you can remove the equipment access panels, locate the flow switch to see if it is in the closed position or even moving/fluctuating. Spa unusable. Water temperature is above acceptable limits.DO NOT ENTER THE WATER! this contact form A slot head screw driver will fit on the rear of the shaft and then try to turn the screw driver to spin the shaft.

HFL Substantial difference between temperature sensors detected.