Home > Sundance Spa > Sundance Error Fl1

Sundance Error Fl1

Contents

FLO or OH Error Code These instructions are for spas with a Flow Switchnota pressure switch. ILOC Error CodeILOC Error Code: Hot Tub is deactivated. We changed the UV bulb last summer and changed out the filters. By his reaction, I get the feeling that he's going to come back and tell me this repair isn't covered under the warranty. have a peek here

This is located underneath the big hump on top of the pump motor. I am having issues with my temp sensor and was about to replace it anyway when the FL1 happened 2 days ago and would not go away. You should have 240vac +/- 10% If you have voltage here you may have a bad circ pump. Welcome, Guest.

Sundance Spa Error Codes

We have turned the hot tub off and on numerous times and tried both filters with no luck. If all else fails contact our Service Support Desk to book a diagnostic and repair of your Sundance Spa. Maybe 03,04,05 ish.

Appreciate the help on this. It was advertised 11/21/2016 11/21/2016 Poolservice123 Was given a Climate Keeper electric oil heater...the top 11/19/2016 11/19/2016 Rico_Soma, eddie22Island I have a Cal-Spas hot tub and I am getting a strange Thank you so much for all of your help! Sundance Spa Flo Error Other then a runaway heat condition you could have a bad temp and or hi-limit sensor, bad PWA, bad control panel or bad transformer.

The initial code was an FL1 and we realized it didn't have enough water in it. Jacuzzi Hot Tub Error Code Fl1 Any ideas? Nigel July 20, 2016 Reply Tim, check the circ point assignments on the PWA with your multimeter. Skip to main content Menu Pools Hot Tubs Bathrooms Service Pool Renovations Water Care Outdoor Living Parts and Accessories Store HomeSupport PostsFL1 CODE FLASHING ON SUNDANCE SPA FL1 CODE FLASHING ON

If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance Spa. Sundance Spa Circulation Pump Problem We do not ship or sell outside of the USA! Q: My control panel read the error code "SN2." What do I do? We have bled the lines and all the jets are working.

Jacuzzi Hot Tub Error Code Fl1

Not sure what else to do. When I turn on the tub...the flow switch stays in contact. Sundance Spa Error Codes A slot head screw driver will fit on the rear of the shaft and then try to turn the screw driver to spin the shaft. Sundance Flow Switch Neither pump 1 or 2 will come on.

Alternatively you could locate the suction line where it is attached to the circulation pump, loosen the gear clamp and the hose and bleed the airlock from there. http://allconverter.net/sundance-spa/sundance-spa-error-flo.html I've been 11/26/2016 11/26/2016 dontrudeau I have a hot tub too series I can't get control panel to 11/25/2016 11/25/2016 Poolservice123 I have a call spa atlantic classic series model 05-5m-ca31. If it doesn't go away you may have blockage in your circ line and or a bad Pressure switch. Purged the air out of the line with a towel and garden hose. Sundance Spa Flow Switch Testing

It stays at 100 degrees even though I have it set at 85. I swapped the wires on the circuit board and put pump 2 where pump 1 is. I will re-verify the flow switch. Check This Out Even with no power to the tub, the flow switch is making contact.

If you power the spa back on and the problem goes away then you are good to go. Sundance Spa Troubleshooting Forum Thanks for being so helpful. Could this be a flow switch issue, if so is there a way to eliminate the switch and verify that the pcb is functional and at the same time determine if

Even with no power to the tub, the flow switch is making contact.

October 20, 2016 Reply Thanks so much, I'll give it my best shot to diagnose it before I buy a new pump. I still suspect a fault on the PWA but I would like to be sure before I order one because I don't wont to be left with the same problem. We have a clean new filter, have tried the towel around the hose trick and still getting the code. Sundance Spa Reset everythign was working. 11/23/2016 11/23/2016 JACUSTOMER-27j3luit- I just purchased a used tub on Craigslist.

Do we still follow the original steps for the FL1 and use a hose and try to clear out the vapor lock? If all else fails contact our Service Support Desk to book a diagnostic and repair of your Sundance Spa. Check for dirty filters first. http://allconverter.net/sundance-spa/sundance-spa-code-fl1.html Check filter for trapped air.2.

Logged Hot Tub Forum Re: Flash FL1 error code fixed « Reply #7 on: January 13, 2014, 11:36:08 PM » Print Pages: [1] « previous next » Hot Tub Forum »