Home > Sundance Spa > Sundance Error Codes

Sundance Error Codes

Contents

Debbie October 19, 2015 Reply Hi, I have a sundance Chelsea. Also make sure you have enough water in the spa for the circ pump to stay primed. Tonja Ellison November 13, 2016 Reply I have a sundance Bahia spa year 2005. SL Indicates spa is in Sleep mode SF Safety Suction, Spa is shut down. have a peek here

If when you apply power to the spa you have 24hr circulation but you just don't have heat you will want to take your multi meter and check for 240vac at Leave a Reply Click here to cancel reply. Std Spa operating in Standard Mode. Please email us at this link:http://www.spaandpoolsource.com/contact-us.aspxTech Support is here to assist you in identifying and selecting the right part for your year and model of spa.

Sundance Spa Flo Error

You may have left this message years ago, I am not sure. Yesterday when we filled it, it said 105. One sensor has detected 118┬║ F at heater.

FLOW SWITCH (Heater is deactivated. Advanced Search Forum > Swimming Pool Care > Spas and Hot Tubs > Trouble with Sundance spa- FLO error and heating issues Welcome to Trouble Free Pool We would like to FREEZE PROTECTIONA potential freeze condition has been detected. Sundance Spa Flo2 Error Could be that part of the plumbing is frozen or you have a bad temp sensor and or bad PWA.

I have left a message for the service tech from the company I bought the spa from, so hopefully I will get to speak to him on Monday....Thanks to all who Sundance Spa Code Fl1 Jets pump(s) operate until the hot tub is out of danger. *Note: The error commonly occurs when the hot tub is first filled because tap water is often very cold. HLoH Hi Limit Over Heat. Has anyone experienced this problem with their Sundance spa? áThe dealer is comming out next week so the spa will have some down time.

It has a flashing fl1 code and is not heating. Sundance Hot Tub Manual Sometimes will work correctly on all speeds, sometimes low only, sometimes when going from low to high it will immediately cut out. If the error returns, contact your Sundance Spa dealer or a qualified service technician. Except for the heater.

Sundance Spa Code Fl1

With the pump off test it again and you should have an infinite reading (open switch). CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional. Sundance Spa Flo Error Maybe 03,04,05 ish. Sundance Spa Temperature Sensor Check for sticking or damaged weir gate.6.

Check to see if you can hear any noise at all from the circ pump with a heat call. navigate here All of this info can be found on your id sticker near the Sentry Control Box. This must be repaired only be a Sundance Spas dealer or qualified service technician. Nigel June 01, 2016 Reply Joe if you have your spa in Standard mode, you have made a heat call and you have no voltage at your Circ point assignments you Sundance Spa Flow Switch

F6 Freeze protection. I just don't think it is working properly. Spa Builders Spa Side Error Codes For more information regarding Spa Builders tech supportclick here Sn1 Nonfunctional high temperature sensor. Check This Out Logged Pathfinder Full Member Posts: 497 Re: Sundance FLO error.... « Reply #4 on: November 13, 2007, 07:08:43 PM » heavy usage, oils lotions can easily clog up a fibre filter

I also noticed the ozone indicator on the control board would go on and off eratically. Sundance Spa Circulation Pump Check for dirty filters first. This must be repaired only be a Sundance Spas dealer or qualified service technician.

Also is it the topside control panel that was replaced recently?

Pump may also be deactivated). If your control panel is"Solid Flo"then the Flow Switch is defective and needs to be replaced.Here is the link for the Flow Switches:http://www.spaandpoolsource.com/sundancespasflowandpressureswitches.aspxHere is the link for the Circulation Pumps:http://www.spaandpoolsource.com/sundancespascirculationpumps.aspx 4. If the FL1 msg does not go away and you have good water movement from your Jet 1 pump on speed 1 you would want to check your connection from the Sundance Spa Heater Not Working A few other #'s I pulled were 230v, 1ph, 60hz.

It's worth the call unless you're handy and plan to DIY. DO NOT ENTER THE WATER! We have bled the lines and all the jets are working. this contact form What do I do?

It stays at 100 degrees even though I have it set at 85. Your assistance/suggestions is greatly appreciated. Patty Dechellis April 13, 2014 Reply so should i turn the jets on? With the circ pump on and the main pump off (Portofino Models with Circulation Pump), test switch operation with an ohmmeter meter in the continuity position, test for continuity across switch