Home > Sundance Spa > Sundance Error Code 616

Sundance Error Code 616

Contents

The timer has been reset to 365 days. ecuadoriaan2586 19.341 görüntüleme 1:41 Balboa GS 100 Hot Tub Quick Set Up Guide From The Balboa Water Group & Hot Tub Suppliers - Süre: 5:12. The Jacuzzi Spa J-135 features two deep bucket seats for the and a lounge. Wait three seconds and then restart the spa to see if error clears up. have a peek here

I really appreciate any help you can lend. HotTubBarn 26.626 görüntüleme 13:31 Ease of Ownership - Sundance Spas - Süre: 3:34. Generated Wed, 07 Dec 2016 02:04:53 GMT by s_ac16 (squid/3.5.20) Contact your Sundance Spas dealer or qualified service technician.

Sundance Spa Uv Bulb

TO reset your ClearRay timer, please refer to our "616" reset instructions here.   Contact UsName * E-Mail * Subject * Message * Download A Copy Of This  Here

© Copyright After the pump primes itself, the error message should go away.5. Indicates a shorted sensor and the heater is disabled.Contact dealer or a service technician.BLB (Flashes in between water temperature and “blb”)Indicates that spa needs a new UV bulb.Replace UV bulb (you See “Summer Log” below.3.

Stands for “Overheat”- and the tub shuts down because water temp is too hot. Did your error code go away? It is the small metal sensor attached to the side of the heater tube. Sundance Spa Flo Error The J- 385 features four deep bucket seats.

Press the (UP) or (DOWN) button to change the statusof the CLEARRAY System from either ON to OFF.Note: If the OFF option is selected, then there is no need to continuewith Their models feature eco-friendly and advanced hydrotherapy options, and Jacuzzi Hot Tubs & Spas is headquartered in Chino, California. Sıradaki ClearRay UV-C Bulb Replacement for 2012+ Jacuzzi and Sundance Spas - Süre: 2:34. Ekle Bu videoyu daha sonra tekrar izlemek mi istiyorsunuz?

Press the Warmer button to scroll to “U”. Sundance Hot Tub Manual If the countdown timer was at 0 the Jet 1 button will reset it. Program setting of spa unit for Economy Mode.3. Take off the spa cover to allow the water to cool down and reduce thermostat settings.

616 Reset Instructions

Means that the ProClarity/Proclear needs to be cleaned or replaced.Remove the filter/debris bag for and clean or replace.Feature not InstalledMessage displays when you try to activate features that are not installed. Your cache administrator is webmaster. Sundance Spa Uv Bulb Contact the dealer or service technician if the problem continues.Blinking Heater IconIcon flashes on and off to let you know that the temperature sensor has detected either a temperature difference of-20°F Sundance Spa Error Codes A new UV bulb can be purchased from a local Sundance Spas dealer.

VISIT US: OFFICIAL WEBSITE CALL US: 844-284-0544 FOLLOW US: CategoriesBackyard FunRecipesOn The GrillIn The GardenHot Tub MaintenanceBackyard MaintenanceFAQSHOP Search for Backyard Blast by TheCoverGuy.com Making the most of your Backyard Heaven! http://allconverter.net/sundance-spa/sundance-error-code-sn3.html A: This means your spa has deactivated itself and is in watchdog mode. I am also 100% certain that I have the ozonator system instead of the UV bulb system. Now, if your error code did not go away, you need to determine if you have a bad flow switch, circulation pump, circuit board, or in rare instances a bad topside Sundance Spa Error Code Flo2

Jets pump 1 will likely deactivate, also.1. sundancespasedm 5.093 görüntüleme 2:24 Dimension One Spa Low Flow Message - Süre: 1:41. Remove hot tub cover to speed cooling. Check This Out If circulation pump is not powering on, try cutting off power at the mainbreaker.

Yükleniyor... Sundance Spa Troubleshooting Fl1 Sometimes it will give us little hints as to what is going on. jacuzziofficial 41.625 görüntüleme 2:07 How to troubleshoot your JACUZZI® Whirlpool On/Off Button-JACUZZI® Tub Parts - Süre: 2:14.

Check for dirty or clogged filter cartridge.3.

The countdown timer for the UB bulb needs to be reset (Section 12.8, page 58). Check for dirty or clogged filter cartridge.3. There are a few steps to take to re-set it, and to erase the function: To Reset: (Do this first)12.8 Programming the CLEARRAY (Ultraviolet) WaterPurification SystemTo access the programming options follow Sundance Spa Not Heating My best guess is that this model topside installed has 'knowledge' of the Clear Ray system, and this is the automated message to tell me to replace it (which, of course,

The Sundance Spa Store Hot Tubs And Leisure 4.839 görüntüleme 1:30 How to repair hot tub error code SN3 - Süre: 17:46. The current status of theCLEARRAY System appears on the LCD display, either ON orOFF.2. Your filters were just clogged restricting flow through them. http://allconverter.net/sundance-spa/sundance-spa-code-fl1.html Jacuzzi Hot Tubs Whitby 10.038 görüntüleme 3:27 Replacing the ClearRay Bulb in a Jacuzzi Hot tub - Süre: 4:03.

A: This is usually a hi-limit sensor. System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps.No action required.Note: this condition often occurs when filling the spa with water since tap water The condition causes the circulation pump to turn off automatically if it’s running in order to avoid adding additional heat to spa water that could cause “Overheat” conditions. Oturum aç 20 2 Bu videoyu beğenmediniz mi?

It is also helpful sometimes to put your spa in economy mode to prevent overheating in the summer. A: This is very much like our "CF" where nothing is actually wrong. All Rights Reserved Send to Email Address Your Name Your Email Address Cancel Post was not sent - check your email addresses! Lütfen daha sonra yeniden deneyin. 22 Mar 2013 tarihinde yayınlandıLearn how to replace your ClearRay UV Bulb in this brief tutorial.

At this point press the warmer button until you see 0. Press and hold the Jets pump 1 and Cooler (-) button at the same time for 3 seconds. 2. Can also mean the hi-limit temp sensor is detecting temp above 116°F/46°C.Please Check FilterMessage displays when the reminder time of the filter has expired. Q:My control panel reads the error code "SN1." What do I do?

The J-355 has a small but good step to enter the hot tub. If buzzing sound or lack of sound is detected, cut off the water to the hot tub – may indicate that pump is notproperly primed.