Home > Sundance Spa > Sundance Error Code 356

Sundance Error Code 356

Contents

DrMoore Logged Jacuzzi Jim Ultimate Member Posts: 3099 Re: Jacuzzi J-340 start up issue, sfw 356, 2004 model « Reply #2 on: February 21, 2013, 05:07:02 PM » Actually I came It can typically be found in the filter compartment and is a quick fix. Causes of the error: Windows Sundance Spa Error Code 356 are caused by misconfigured system files. To freeze or not freeze?? have a peek here

I needed a plan and to know how get through a freezing night. poolguy810 and other Pool and Spa Specialists are ready to help you Ask your own question now Now my PC is much faster and more importantly I have stopped seeing this error! This message will disappear when the circuit board temperature drops below acceptable limit. A sloid white light indicates that all operations are normal.

Sundance Spa Flo Error

It rolls, ICE, 45, sometimes a 356 or something like that. Welcome, Guest. Could it be just that single cap??? : I have an '05 Sundance Palermo I got in '05, I use it EVERY night (so : I'm pissed it is not working!) CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional.

It is impossible to get rid of, then we had this drama. I'm pretty sure that I will need a new pump, and possibly a new heater but am most concerned about how to proceed tonight, and until I can get a technician Any time it calls for heat it does this. : BUT, if I run both pumps (heater off) it does this too! Sundance Spa Troubleshooting Fl1 Richmond, CA 94804 (510) 234-7920 Login|Contact Us Pool and Spa Questions about Pool Repair?

Not sure whats going on, with a air lock you should get a FL1 error. 356 is the chip, 888 is some kind of misc code. Sundance Spa Troubleshooting Now it won't even come up and run the circ pump even with the heater turned off (temp set below water temp). A: This is usually a hi-limit sensor. Proper flow of water is inhibited or a flow switch has malfunctioned.

Just connected it 12/1/2016 12/1/2016 Poolservice123 The cal spa hot tube has two settings jet 1 and jet 2. Sundance Spa Not Heating Remove hot tub cover to speed cooling. Q: My control panel reads the error code "OH." What do I do? What do I do?

Sundance Spa Troubleshooting

Fiddled with flow switch, I have 3 of them now, but pretty sure problem with circ pump. no more errors and officially back in action. Sundance Spa Flo Error Error Logo Light Meaning Overheat Protection (Heater is deactivated, filter/circulation pump is activated). Sundance Hot Tub Manual The filter/circulation may also be deactivated).

I dont think the cabinet has room for a heater. http://allconverter.net/sundance-spa/sundance-error-code-sn3.html Modern hot tubs with electronic controls feature spaside keypads with digital readouts. So only kirby, mario, lloyd, and the other guy (i forgot... RISK OF HYPERTHERMIA (OVER-HEATING) CAUSING SEVERE INJURY, BURNS, OR WELTS. Sundance Spa Flo2 Error

A: This is usually the temperature sensor. Contact your Sundance Spas dealer or qualified service technician. *Note: This message can also appear if the pump has not regained prime after the hot tub has been drain and refilled. Thanks for helping me tonight. Check This Out The pump is moving water, the little valve thing (hub called it a cylanoid?) is pushing water through.

The spa is 6 years old....magic age of breakdown :(Customer: also, I did get the big jets to circulate a few times, but can't get them to circulate every time I Sundance Spa Flow Switch No corrective action is necessary. Error Codes & Helps - US Parts Center - Hot tub accessories..

thx....guess you forgot how to get to my house, to do ur magic while I'm in house :-) Logged Jacuzzi Jim Ultimate Member Posts: 3099 Re: Jacuzzi J-340 start up issue,

tub 11/30/2016 11/30/2016 JACUSTOMER-27j3luit- I have a, whirlpool jacuzzi, We do not knowe the model. What do you think? Please try again. Sundance Spa Circulation Pump Q: My control panel reads the error code "---".

Thank you soooo much for your help. Sign In All Activity Home Theme Default (Default) Copy of Default Contact Us PoolSpaForum.com Community Software by Invision Power Services, Inc. × Existing user? Carolyn Says: at 3:47 AM Just ran this on my wife's computer and for the first time in a long time, it finally works again! http://allconverter.net/sundance-spa/sundance-spa-code-fl1.html Read a post online they don't make the Laing pumps [from Hungary anymore] [have two of them now too].

The heater would come on, : REAL hot water could be felt at the circ pump output, then it would : go to "Ho" and shut the heater down. I specialize in electrical questions and I am most familiar with spas that were.Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery All sorted now. STEP 2:Click the "Quick Scan" button.

Did you all get a chance to try the power shut down for ten minutes to see if it cleared anything up?Customer: no, I will turn it off. A solid red light indicates that immediate attention is required to clear or fix an error code. Sometimes, it is just a little power spike and can be fixed by turning the breaker off for 10 seconds and back on.